I am using the 358-155-TC ELCO bullet from NOE I am looking for a fast powder like titegroup that works good with lead … 9mm Luger / 9mm Parabellum (147 GR) Handload Data reloading data with 55 loads. Double Pistol Case Shop Now .458 SOCOM (.458) 350gr RS Shop Now . They've got load data for 124 and 100 grain FMJs, just not 115. **All remanufactured ammo is 100% fully reconditioned in house back to S.A.A.M.I.

Powders include Winchester, Vihtavuori, Alliant, IMR, Hodgdon, Accurate, Ramshot 147 gr blue bullet, CCI primer, Coal 1.145 3.6 grains WST = 134PF out of my STI marauder 9mm and holds a off hand 2" group at 25 yards. I use a Lee turret with the AutoDisk, and I'm finding that one cavity is at or lower than the recommended min charge, and the next cavity up is at or higher than the recommended max charge. I have been loading .45 exclusively with Titegroup and this is my first time with 9mm. Load Data for 147gr powder coated 9mm. These are 147gr Berry's copper plated loaded to minor power factor strength. Titegroup was my go to powder for years with 147gr plated bullets in 9mm. Just looking for others using hbfp berrys and a safe load range and seating depth, as there isn't any published data I can find for this style bullet.

The current Lyman manual (49th Edition) does not have load data for anything heavier than 147 grains, but older manuals do. Powders include Winchester, Vihtavuori, Alliant, IMR, Hodgdon, Accurate, Ramshot Tried these at 5.8 gr.

** ... My personal load is 3.0gr Titegroup, Fed primer, 147gr Ibejihead, 1.12" OAL. 9mm 147gr FP Competition Load *REMANUFACTURED* Velocity 4″ 876 FPS Packaged in a 50, 250, 500 or 1000 round boxes. But you may need to adjust for your barrel. 9mm 147gr FP Competition Load *REMANUFACTURED* 50rds - Precision ONe Ammunition 9mm 147gr FP Competition Load *REMANUFACTURED* Velocity 4″ 876 FPS Packaged in a … Load Data Suggestions for 124 gr Berry's Plated 9mm. specs. I started casting and coating my own bullets in HI-Tek and Titegroup just doesn't work well with cast. hs-6 at 1.08 oal.

Powder Bul Weight C.O.L.

I'd normally use a slower powder with the 147 grn bullet in the 9mm, Titegroup may work though. This load will also be used with my suppressor. Using bullets from Hornady HPBT-XTP, Speer TMJ-FN. 2.8 gr. Min Charge Max Charge Optimal Charge Bullet Make Bullet Type Primer Notes; Accurate - Nitro 100 NF: 115 gr. bombmaster 1,263 1 Using bullets from Hornady HPBT-XTP, Speer TMJ-FN. Please list a favorite load if you have one. Cabelas had a 20% off sale on bullets so I picked up some Berrys 124 grain plated bullets and thought they would be good for my first attempt at reloading. Bullets are Zero 147gr FMJ, Win SPP, Mixed brass, and Titegroup powder. This is a discussion on Load Data Suggestions for 124 gr Berry's Plated 9mm within the Ammo and Reloading forums, part of the Gun Forum category; Hello, fellow SIG lovers.

The 3.4gr Titegroup under 147gr Hornady FMJ RN is pretty soft and if you've ever shot Fiocchi, equates to their 158gr subsonic load. As others said right around 4.0 for 124s. 9mm 135gr Hollow Base Flat Point Shop Now .

I load to an OAL of 1.150 (COL max is 1.160") I'm typically loading a berry's 124 with 4.1grs. 100gr HHP Shop Now . (only powder i could find that might work) Now i see data using 3.2 grains as a starting load with the 147's.I am wondering if I could use this powder weight with the lighter bullets as well.I am concerned with the cycling of my stock G19 Gen 4 as well. I've been shooting berrys 9mm in a P95. 124 gr roundnose with 6.2 gr hs-6, oal @ 1.113. I jumped into reloading and bought a lot of equipment, supplies, and accessories. Load data for our Superior Plated Bullets® can be found in any manual or on any powder manufacturer’s website. Starting Load Grains3.2 Velocity (ft/s)855 Pressure22,500 CUP Maximum Load Grains3.6 Velocity (ft/s)929 Pressure27,500 CUP Here is some data from the Hodgdon site. Any additional information you can give me about precautions with the Rainier plated bullets, I would appreciate it.